News Center

Pilates wall-mounted training table spring

The Pilates wall-mounted spring and the spring used in the Pilates wall-mounted multifunctional training table are one of the accessories in the Pilates equipment.

Heat Treatment Strengthening Technology of Stainless Steel Spring

Protective atmosphere heat treatment. In our country, the heat treatment of stainless steel springs with wires less than 15mm, oil-quenched and tempered steel wires and toughened steel all use protective atmosphere heat treatment. Protective atmosphere heat treatment can ****** surface decarburization and oxidation, improve the surface quality of the material.

Introduction to the reasons for the tilt of the spring after full pressure

The steel wire used to make the spring is 1.5, the outer diameter of the spring is 8.1, and the height is 12.3 (13 after full compression, not fully compressed). After a lot of debugging, it can be seen that this may be the residual deformation of the spring. There are four possible reasons:

Quality Requirement of Wire for Vehicle Suspension Spring

The wire rod for car suspension spring has strict requirements on the purity, dimensional accuracy and surface quality of steel. Practice has proved that the diameter accuracy of wire rod is of great significance to reduce wire drawing die wear, reduce energy consumption, reduce wire breakage and ensure stable drawing. The diameter tolerance of wire rod for suspension spring shall be controlled within ± 0.2mm, and the ovality shall not be greater than 60% of the diameter tolerance. The cracks, folds, scratches and other defects on the surface of the wire seriously affect the quality of the wire and reduce the fatigue life of the suspension spring. The wire surface shall be smooth and free from cracks, folds, scarring, ears, etc. The size of local defects such as bumps, pits and pockmarks shall not be greater than 0.10mm. The mechanical properties of the wire rod are better, and the fluctuation is small. The tensile strength fluctuation of the wire rod is less than or equal to 40MPa, the area shrinkage fluctuation is less than or equal to 15%, the volume fraction of sorbite is more than or equal to 85%, the free ferrite has a great influence on the fatigue life, the volume fraction should be controlled within 1.5, the grain size is above 8, and no martensite is allowed.

Treatment process of disc spring blackening

Alkaline chemical oxidation treatment black, is the qualified spring processed into a concentrated alkali solution containing heat treatment, so that the surface of the spring to obtain a thin layer of dense oxide film, the oxide film has anti-corrosion effect.

What role can car suspension springs play

From the perspective of product use effect, what role can automobile suspension springs play? The following are some key points of the use of automobile suspension springs.

Fault Treatment Method of Spring Testing Machine

1999 this happens when the electronic testing machine is turned on, the CPU working frequency (11.0592MHz) may be abnormal, and the crystal oscillator will be replaced on the same day. If the input terminal voltage of the two sensors is too high (usually a few millivolts), check whether the sensors are normal. The general data obtained by electrically blocking the measurement sensor with a multimeter are: the input terminal is about 405Ω; the output terminal is about 340Ω; the resistance value of the two leads at either end and the other end is 280 Ω. Note: the sensor input, the output of the data sometimes with different manufacturers will have a certain change, but the change is a certain proportion. If the comparison voltage of the two operational amplifiers is not normal, measure whether the resistance of pin 2 and pin 3 of the amplifier has changed. If the resistance value occurs, it should be replaced. If the above conditions are normal, the operational amplifier of the electronic testing machine is damaged and should be replaced. If the 220V voltage of the power supply is unstable, a regulated power supply shall be configured.

Development and technical advantages of spring industry

Although the spring industry is a small industry in the entire manufacturing industry, its role cannot be underestimated. The country's industrial manufacturing industry and automobile industry must accelerate the development, and the spring industry, as one of the basic parts and components, needs a more advanced period of development to adapt to the rapid development of the country's entire industry. At present, the output of China's spring industry tends to be saturated. According to expert statistics, China's spring production has reached 4 billion pieces. There are 21 categories and more than 1600 varieties of spring products, mainly including valve springs, suspension springs, diaphragm springs, damping springs, hydraulic springs, oil pump springs, butterfly springs, high temperature springs, circlip springs, tension springs, torsion springs, compression springs, scroll springs and heterosexual springs. At this stage, China's spring products are mainly low-tech general springs, and only a few large-scale high-tech products such as heterogeneous parts and cross-sectional products can be produced.